Infant Radiant Baby Warmer


Infant Radiant Baby Warmer

Specifications

Dimesnions 85 cms(L) x70 cms(W)x185 cms(H)
Weight 70 Kgs (nice 2010BC)
Mattress 73 cms (L) x 53 cms (W) x 5 cms (H)
Mattress from floor 95 cms
Maximum load 10 Kgs
Side panels Aluminum hinged acrylic panels
Maximum load for monitor shelf 4.5 Kgs
Heater module swivel ±90 Degree

Features:

  • Micro Controller based Electronics
  • Controls - Servo Skin/ Apgar
  • Pre-warm - Use the equipment with 30% Heater Output in Manual Mode.
  • Programmable Mute time
  • No need of calibration required for temperature probe.
  • High Intensity Quartz Heating element for effective Radiation (Ceramic heater Optional)
  • Halogen Observation Lamp
  • The Heater Module rotates 90° to both sides to facilitate
  • X-Ray Procedures.
  • The Parabolic Reflector is designed to send uniform heat to the bed surface.
  • Memory Backup to restore set temperature and previous mode, in case of power failure.
  • Optimum Bed dimensions ensure optimum work space for the nursing staff.
  • Comprehensive Alarms and safety cut-offs.
  • Alert (Alarm) when sensor is detached from the patient's skin (optional)
  • Instant Warming and Uniform heating

 

Controller

  • Electronics : High speed micro controller
  • Mode of operation : Servo skin, manual & apgar
  • Skin mode control range : 30 Deg. C to 38 Deg. C
  • Manual mode timer : 1 min to 15 mins (selectable), 15 mins to 30 mins (optional)
  • Apgar timer : Alerts at 1, 5, 10, 15 & 20 mins (selectable)
  • Percentage of heater output : 10% to 100% in 10% increments
  • Memory back up : Equipment restores the previous settings
  • Programmable mute time : User can select the mute time
  • Safety heater cut off : If the skin sensor is removed from the baby's skin
  • Over temperature heater cut off : If the skin temperature is >39 Deg. C in any skin/manual mode
  • Temperature sensor (probe) : Thermistor sensor
  • Accuracy of skin sensor : ±0.1 C
  • Accuracy of skin probe Interchangeability : 0.2 C
  • Calibration of skin sensor (probe) : No need of calibration after Changing new probe
  • Heater element : Quartz Infrared heater Ceramic heater (optional)


Other Details

  • Power rating : 230V AC, 50Hz, 700 W
  • Maximum heater wattage : 600 Watts
  • Maximum power requirement : 700 Watts
  • Examination light : 12V, 50W Halogen lamp
  • X-ray facility : Underneath the bed
  • Mattress tilt : ±30 degrees on both sides
  • IV pole : Maximum load 2.2 Kg
  • Pump mounting pole : Maximum load 2.2 Kg
  • Castor : 4” castors 4 Nos. (2 with brake & 2 without brake
  • Monitor shelf : 2 Nos. Fixed
  • Height adjustable heater module : Available only in nice 2010
  • Cabinet : Available only in nice 2010BC
  • Operating noise level : <50 dBA


Controller Alarms:

  • Check patient If the skin sensor is removed from
  • the baby's skin
  • Skin temperature high > 1.0 C from the set temperature
  • Skin temperature low < 1.0 C from the set temperature
  • Skin temperature probe fail Probe short or open
  • Over temperature If skin temperature is 39 C
  • Heater fail Heater defect
  • System fail Electronic component defect
  • Power fail AC power interruption


Environmental

  • Operating temperature - 15° C to 35° C
  • Storage temperature - -20° C to 60° C
  • Operating humidity - 5% to 90% RH, non condensing
  • Storage humidity - 0% to 99% RH, non condensing
  • Altitude - Sea level to 1-9 miles, 3 Km
  • Quality - ISO 9001:2000 & ISO 13485:2003
  • Electrical & product safety - IEC 60601-1, IEC 60601-1-2, IEC 60601-1-4, IEC 60601-2-21

Yes! I am interested



  • Explore More Products




Looking for "Infant Radiant Baby Warmer" ?

 



Looking for Product Name ?